Printer model
ELEGOO Neptune 4 Pro: nozzle kits, versions and specs
ELEGOO's Neptune 4 Pro specs, and why its nozzle kits fit only the Type-C version of the Neptune 4 and 4 Pro, not the ribbon-cable units.
Also listed as Neptune 4
We may earn a commission if you buy through links on this page. How we make money
Short answer
Check your version first: ELEGOO lists its Neptune 4-series hardened steel and brass nozzle kits for the Type-C Neptune 4 and 4 Pro only, not the ribbon-cable units. ELEGOO's global page gives the 4 Pro a 300 °C nozzle maximum, a 225 x 225 x 265 mm build volume, Klipper pre-installed and a dual-gear direct extruder. See Neptune 4 ribbon cable vs Type-C.
What fits
- HotendMicro Swiss FlowTech hotend for ELEGOO Neptune 4 / 4 Pro (M3107)Check price on Amazon
Key facts
- Build volume
- 225 x 225 x 265 mm[1]ELEGOO's stated print volume from its global spec table, not the plate outline.
- Motion system
- Not confirmed
- Stock extruder
- Dual-gear direct extruder[1]
- Stock hotend
- Not confirmed
- Nozzle standard
- Not confirmedELEGOO's MK8 statement is in its Neptune 3 FAQ and covers the Neptune 3 series only. Use ELEGOO's Neptune 4-series nozzle kits and their version rule.
- Stock nozzle
- Not confirmed
- Max nozzle temperature
- 300 °C[1]From ELEGOO's global product page.
- Max bed temperature
- ELEGOO's global page lists 100 °C[1]We did not read ELEGOO's other regional listings, which may state a different figure. Check your own unit's documentation.
- Firmware
- Klipper, pre-installed[1]
- Latest listed firmware
- Not confirmedELEGOO's product page gives no firmware version.
- Power input
- 115/230 V, 50/60 Hz[1]ELEGOO's spec-table voltage row. The page does not say how the voltage is selected and gives no rated printer power, only heater outputs (100 W + 150 W segmented bed). Check the label on your unit and follow ELEGOO's manual.
- Hardware revisions
- Ribbon-cable and Type-C versions; ELEGOO's Neptune 4-series nozzle kits fit only the Type-C Neptune 4 and 4 Pro[2][3]ELEGOO's kit pages carry a 'Verify Version Compatibility' notice. Ribbon-cable Neptune 4 and 4 Pro units are excluded.
- Maker maintenance rules
- Not confirmed
- Documented upgrade kits
- ELEGOO hardened steel nozzle kit and multi-size brass nozzle kit for the Neptune 4 series (Type-C version only)[2][3]ELEGOO's version rule covers these nozzle kits only, not extruders, cables or plates.
- Recall status
- No recall found on 2026-10-08[4]On 2026-10-08 we found the Bambu Lab A1 recall as the only 3D printer recall in CPSC's notices. That is a dated search, not proof that no recall exists.
- Not confirmed
- Not confirmedELEGOO's global product page states none of these, and we did not read the US listing.
Watch out for
- ELEGOO lists its Neptune 4-series hardened steel and brass nozzle kits for the Type-C Neptune 4 and 4 Pro only. A ribbon-cable 4 Pro is excluded, so check your version before ordering.
- ELEGOO's Neptune 3 FAQ (MK8 nozzles, a 27 mm all-metal throat) covers the Neptune 3 series, not the Neptune 4.
- ELEGOO's authorized-reseller page names no Amazon or AliExpress store; for the US and Canada it points to us.elegoo.com and ca.elegoo.com.
What fits
Product details below are the seller's own description unless a source is shown. Pick the variant named for each item.
Hotend
Micro Swiss FlowTech hotend for ELEGOO Neptune 4 / 4 Pro (M3107)Choose the Neptune 4 / 4 Pro version (M3107), not the Plus / Max version (M3108).
Micro Swiss names the Neptune 4 and 4 Pro and says firmware and z-height stay stock. It makes no ribbon-cable vs Type-C statement, so check with Micro Swiss for your unit.
The Neptune 4 (non-Pro) shares the Type-C-only rule for ELEGOO's Neptune 4-series nozzle kits. The build volume, temperatures and voltage on this page are ELEGOO's Neptune 4 Pro figures; we did not confirm them for the Neptune 4.
Questions
Do ELEGOO's Neptune 4 nozzle kits fit my Neptune 4 Pro?
Only the Type-C version. ELEGOO lists its hardened steel and multi-size brass nozzle kits for the Type-C Neptune 4 and 4 Pro only, so ribbon-cable units are excluded.[2][3]
How hot can the Neptune 4 Pro nozzle and bed get?
ELEGOO's global product page lists 300 °C for the nozzle and 100 °C for the bed. We did not read ELEGOO's other regional listings, so check your own unit's documentation for the bed figure.[1]
Does the Neptune 4 Pro run Klipper?
Yes. ELEGOO says the Neptune 4 Pro ships with Klipper firmware pre-installed. Its product page gives no firmware version, so use the firmware ELEGOO publishes for your exact model.[1]