Printer model
Sovol SV08: specs Sovol lists and what is not confirmed
Sovol's SV08 specs: CoreXY, 350 x 350 x 345 mm, up to 300 °C, 0.4 mm nozzle, and why nozzle swaps with the SV06 ACE are not confirmed.
We may earn a commission if you buy through links on this page. How we make money
Short answer
Sovol lists the SV08 as a CoreXY printer with a 350 x 350 x 345 mm build volume and a nozzle temperature of up to 300 °C, with a 0.4 mm nozzle included. Sovol does not document whether SV08 nozzles interchange with the SV06 or SV06 ACE. We do not publish the SV08's power-supply row, which does not match its other specs.
What fits
- HotendMicro Swiss FlowTech hotend for Sovol SV08 (M3110)Check price on Amazon
- Hardened steel nozzlesSovol hardened steel nozzle kit for SV08 / T300, 0.4 mm x2Check price on Amazon
- Heater and thermistor setSovol SV08 extruder replacement kit (ceramic heater, nozzle thermistor, silicone sleeve, heater clip)Check price on Amazon
Key facts
- Build volume
- 350 x 350 x 345 mm[1]
- Motion system
- CoreXY[1]
- Stock extruder
- Direct drive; Sovol's spec table says planetary gear and its FAQ says dual-gear[1]Sovol's two descriptions differ.
- Stock hotend
- Not confirmed
- Nozzle standard
- Not confirmed
- Stock nozzle
- 0.4 mm included; 0.2, 0.6 and 0.8 mm options[1]
- Max nozzle temperature
- Up to 300 °C[1]
- Max bed temperature
- Not confirmed
- Firmware
- Not confirmedSovol's page says only that the SV08 supports open-source firmware.
- Latest listed firmware
- Not confirmed
- Power input
- Not confirmedSovol's power-supply row does not match the rest of its specs, so we do not publish it. Check the manual and the label on your unit.
- Hardware revisions
- Not confirmed
- Maker maintenance rules
- Not confirmed
- Documented upgrade kits
- Not confirmed
- Recall status
- No recall found on 2026-10-08[2]On 2026-10-08 we found the Bambu Lab A1 recall as the only 3D printer recall in CPSC's notices. That is a dated search, not proof that no recall exists.
- Not confirmed
- Not confirmedSovol does not document it; only an owner forum thread claims it.
Watch out for
- Sovol does not document nozzle interchangeability between the SV08, SV06 and SV06 ACE. Treat forum claims as owner reports, not fit.
- Sovol's spec table and FAQ describe the SV08 extruder differently (planetary gear vs dual-gear direct drive).
What fits
Product details below are the seller's own description unless a source is shown. Pick the variant named for each item.
Hotend
Micro Swiss FlowTech hotend for Sovol SV08 (M3110)Choose the FlowTech for Sovol SV08 (M3110).
Micro Swiss names the SV08 and says no firmware change is needed. The SV08 MAX and Zero are not named.
Hardened steel nozzles
Sovol hardened steel nozzle kit for SV08 / T300, 0.4 mm x2Choose the 0.4 mm x2 kit for SV08/T300.
Sovol lists these hardened steel nozzles for the SV08 and T300, and suggests 0.6 or 0.8 mm for carbon fiber or glass fiber filaments.
Heater and thermistor set
Sovol SV08 extruder replacement kit (ceramic heater, nozzle thermistor, silicone sleeve, heater clip)Choose the SV08 extruder replacement kit, not the SV08 MAX / Zero kit.
Sovol's own set of ceramic heater, nozzle thermistor, silicone sleeve and heater clip for the SV08. Sovol states no electrical rating; follow Sovol's instructions for the swap.
Questions
Do SV06 ACE nozzles fit the Sovol SV08?
Sovol does not say. Only an owner forum thread claims the SV08 takes the same nozzles as the SV06 ACE, so we do not treat it as confirmed.
What is the Sovol SV08 build volume?
Sovol lists 350 x 350 x 345 mm, on a CoreXY frame, with a nozzle temperature of up to 300 °C.[1]