Extruder system
BIQU Panda Revo: Bambu P1 and X1C fit and flow claim
BIQU's Panda Revo hotend for the Bambu Lab P1P, P1S and X1C: Revo nozzles, a 300 °C spec, and BIQU's 40 mm³/s figure with its test conditions.
We may earn a commission if you buy through links on this page. How we make money
Short answer
BIQU lists the Panda Revo as compatible with the Bambu Lab P1P, P1S and X1C, using E3D RapidChange Revo nozzles except Revo Belt. BIQU's spec table gives 300 °C, and BIQU states a maximum flow of 40 mm³/s, measured with HS PLA at 260 °C and a 0.4 mm High Flow nozzle. BIQU's page does not mention the X1E or the A1 series.
Key facts
- Type
- Hotend for Bambu Lab printers, using E3D Revo nozzles[1]BIQU says it comes from an official collaboration with E3D.
- Filament size
- Not confirmed
- Gear ratio
- Not confirmed
- Published E-steps
- Not confirmed
- Drive gears
- Not confirmed
- Max temperature
- 300 °C (BIQU spec table)[1]Feature text on the same page gives higher figures that conflict with the spec table; we publish only the spec-table value.
- Nozzle standard
- E3D RapidChange Revo nozzles, except Revo Belt[1]
- Nozzle change
- Not confirmed
- Heater
- Not confirmed
- Printers the maker names
- Bambu Lab P1P, P1S and X1C[1]BIQU does not mention the X1E or the A1 series.
- Maker flow figure
- 40 mm³/s, with HS PLA at 260 °C and a 0.4 mm High Flow nozzle (BIQU)[1]The maker's own figure under its stated conditions, not an independent measurement.
- Outside measurement
- Not confirmed
- Where the maker sells
- Not confirmed
- Not confirmed
- Not confirmedBambu Lab's hotend pages returned errors on 2026-10-08.
Watch out for
- BIQU names the P1P, P1S and X1C only. Do not assume fit on an X1E or an A1-series printer.
- Quote BIQU's 40 mm³/s only with its conditions: HS PLA, 260 °C, 0.4 mm High Flow nozzle.
- Revo Belt nozzles are the exception BIQU names; other RapidChange Revo nozzles fit.
What fits
Product details below are the seller's own description unless a source is shown. Pick the variant named for each item.
Panda Revo hotend
BIQU Panda Revo hotend for Bambu Lab P1P / P1S / X1CChoose the P1P/P1S version (1060000654); the X1C version (1060000659) is a separate listing.
BIQU lists the Panda Revo for the Bambu Lab P1P, P1S and X1C.
Revo nozzle
E3D Revo brass nozzle, 0.40 mm (RC‑NOZZLE‑0400‑AS‑SPK)Choose the single 0.40 mm brass Revo nozzle (RC-NOZZLE-0400-AS-SPK).
BIQU says the Panda Revo takes RapidChange Revo nozzles, except Revo Belt.
Questions
Which Bambu Lab printers does the Panda Revo fit?
BIQU lists the Bambu Lab P1P, P1S and X1C. Its page does not mention the X1E or the A1 series. See P1 and X1 hotend upgrades.[1]
Is the Panda Revo's 40 mm³/s independently measured?
No. It is BIQU's own figure, measured with HS PLA at 260 °C using a 0.4 mm High Flow nozzle.[1]